Mr Browning.

[kiwi hunter]

I own two xbolts, one is standard and the other a long range mod with a 26 inch barrel. Both are in 300 wsm cal.
What brasses me off is the damn trigger, you can't seem to get the let off much below 3 lb, now for long range shooting that's a joke.
Here in OZ I have a mod 70 also in 300wsm, now Winchester have got their act together and I can adjust the letoff down to 1lb or so, an actual hair trigger which is a joy for prone or off sticks.
So my question why does Browning do this again in the xbolt 2 model?

 

[longbow51]

Lawyers.

 

[std7mag]

I own two xbolts, one is standard and the other a long range mod with a 26 inch barrel. Both are in 300 wsm cal.
What brasses me off is the damn trigger, you can't seem to get the let off much below 3 lb, now for long range shooting that's a joke.
Here in OZ I have a mod 70 also in 300wsm, now Winchester have got their act together and I can adjust the letoff down to 1lb or so, an actual hair trigger which is a joy for prone or off sticks.
So my question why does Browning do this again in the xbolt 2 model?

It's not the "let off" that you're talking about. It's how the trigger "breaks or the pull weight".
Let off is how far a trigger travels on a double action firearm to reset the trigger for the next shot.
For example a striker fired, semi auto pistol.
You pull the trigger and the gun fires. How far you have to release the trigger to reset so that you can pull it and fire the next round.

If it were me, I'd check out Trigger Tech and see what they offer for it.

BTW, my BR rifle has a trigger set 2oz.
My hunting rifles are at 2lb.

 

[kiwi hunter]

Lawyers.

So Winchester doesn't worry about them?
I don't see why I should need to buy any accessories.

 

[VMHunter]

Timney probably has a fix for it.

 

[Wind Gypsy]

So Winchester doesn't worry about them?
I don't see why I should need to buy any accessories.

Or tikka, sako, blaser, any m700 pattern that uses a timney/triggertech/bix, etc.

 

[EKYHunter]

Get the M*CARBO trigger spring for your Brownings and you’ll be good to go. Easy fix.

 

[kiwi hunter]

the mxcarbo only goes down to about two pounds, totally useless to me

Get the M*CARBO trigger spring for your Brownings and you’ll be good to go. Easy fix.

 

[EKYHunter]

the mxcarbo only goes down to about two pounds, totally useless to me

Mine goes to 1.5 and that’s where I stopped but there was room to go less. Just saying.

 

[huntnfisher]

Mine goes to 1.5 and that’s where I stopped but there was room to go less. Just saying.

The MCarbo springs work very well. I have 2 X Bolt's...a Maple Medallion in 6.5 CM, and a White Gold Medallion in .30-06, both with MCarbo springs and they are great! I have them both set around 2#, and could have went lower. An easy and inexpensive upgrade.

 

[longbow51]

So Winchester doesn't worry about them?
I don't see why I should need to buy any accessories.

Winchester is a very old design. My gunsmith predicts that all factory triggers will eventually have something like the Ruger American Gen 2 trigger with an extra safety device built in (trigger blade safety), so that the trigger can't go off if bumped.

 

[kiwi hunter]

Winchester is a very old design. My gunsmith predicts that all factory triggers will eventually have something like the Ruger American Gen 2 trigger with an extra safety device built in (trigger blade safety), so that the trigger can't go off if bumped.

My friend experimented with the Winchester and no matter what the trigger held.
I might try a ballpointpen spring just to see if that works, importing a firearms part is a hard job here in NZ.