Woodworking Hunt Talkers?

I'm pretty stoked on how my new staircase is taking shape, especially the handrail, the temporary stair treads will come out soon and my pretty maple ones will match the railing after sanding and oil...then to finish the awful job of chipping out the rest of the floor tile so I can install the wood floor.
View attachment 185184
Better think twice about the wood floor idea. Those dogs will wreck it. Been there! I suggest replacing with ceramic that looks like wood. Looks good and wears like iron. Dogs can't hurt it. No worries about water on the floor if sliding door is left open. Lots of patterns are available. When removing the ceramic, pull up the underlay too. Should come up easily if it's only been nailed down (hopefully some cheap contractor used box nails instead of screws). Even if screwed down you'll likely tear up the surface of underlay trying to remove tile. Pull it all up and start over. If they used mud board underlay it will be messy but I really doubt you'll be able to reuse it. Too much hassle to try. Also, if you decide to go with wood look ceramic and replace underlay, do not use the special underlayment plywood marked for screw placement. It's too smooth and tile glue doesn't stick to it well. Just use quarter inch regular plywood and mark it with chalk string. Rougher plywood bonds better to glue. Or you can pay the bucks for mudboard but I've found it's unnecessary even in heavy use areas like my back porch.

Edit: In my kitchen I used quick-set grout to lay the tile and the crap didn't hang onto several tiles that eventually loosened and cracked. To replace them I bought a grout cutter blade for my Dremel Multi Tool (NOT the rotary tool). It did a good job of removing the grout AND the tile cement. I heartily reccomend one for pulling up your tile. Laid replacement tiles with white latex grout in a tub. Takes longer to set up but never fails. Use the latex binder in a jug to mix with grout instead of water.
 
Last edited:
Lots of cool stuff here. Always fun to see others projects to come up with inspiration for your own. My last two below.

Planning to build a stock for my 300 mag but wanted to practice on something else first. Laminated a few walnut boards for the 10/22. My son saw it and claimed it as his own.
 

Attachments

  • 23E4422D-3EF7-4B97-B8E6-2FCCA5CCA209.jpeg
    23E4422D-3EF7-4B97-B8E6-2FCCA5CCA209.jpeg
    3.5 MB · Views: 25
  • 4A2433EE-71D0-4026-B629-B97EB5EC969F.jpeg
    4A2433EE-71D0-4026-B629-B97EB5EC969F.jpeg
    2.2 MB · Views: 25
Lots of cool stuff here. Always fun to see others projects to come up with inspiration for your own. My last two below.

Planning to build a stock for my 300 mag but wanted to practice on something else first. Laminated a few walnut boards for the 10/22. My son saw it and claimed it as his own.
How did you inlet the stock? Did you use some sort of router jig or just go really slow with chisels? Looks good, I really like the table too.
 
How did you inlet the stock? Did you use some sort of router jig or just go really slow with chisels? Looks good, I really like the table too.
Thanks. I made a router jig and snuck up on it. The tapered barrel was a bit tougher trying to get the lines right. Cut it on the router small and used a dremel and sanding to get it where I wanted it.
 
Thanks. I made a router jig and snuck up on it. The tapered barrel was a bit tougher trying to get the lines right. Cut it on the router small and used a dremel and sanding to get it where I wanted it.

This is what I use. They are made for octagons and rounds.

You have much courage starting with a router. I cannot screw up anything faster than I can with a router :)
 
I’ve always thought the router is the most dangerous tool in my shop. The hand tool looks nice, might have to try that on the next one.
 
Not in the same league with you guys but a couple of ammo boxes I made that hold 165 rounds each. They weigh a ton when full.

And then a nice 23 ft x 32" dbh red oak the I sold this morning.
 

Attachments

  • 20210622_205042.jpg
    20210622_205042.jpg
    4.1 MB · Views: 21
  • 20210621_164820.jpg
    20210621_164820.jpg
    3 MB · Views: 22
Live edge black walnut that I cut down from my parents’ back yard—finally got it finished up this year. I also build this pedestal table last Fall from Red Oak.

Some of you guys are REALLY talented!
 

Attachments

  • AC403E42-3914-4215-A6D6-E244C90C63CF.jpeg
    AC403E42-3914-4215-A6D6-E244C90C63CF.jpeg
    2 MB · Views: 18
  • 7B5DDC78-3AED-4095-906A-C25519396E1F.jpeg
    7B5DDC78-3AED-4095-906A-C25519396E1F.jpeg
    3 MB · Views: 18
  • 41600925-24EB-4DDF-9080-D40DFFE25E31.jpeg
    41600925-24EB-4DDF-9080-D40DFFE25E31.jpeg
    2.5 MB · Views: 18
Kenetrek Boots

Latest posts

Forum statistics

Threads
113,668
Messages
2,028,993
Members
36,275
Latest member
johnw3474
Back
Top