308 Moses

[kodiakisland]

When I lift the bolt with ease, literally pull it back brass pops out inspect it, primer cup is still round, no crater that is telling me what I’m wanting to know.
With the bigger magnum cartridges I have noticed the base junction show’s you pressure if it’s there really fast! I have been shooting the 300 Norma mag before going Moses. I was maxed out at 88gr of n570 with a 215 @3160fps, I could have dropped the load down but the node was there so I took advantage of it as most do.

case volume is consistent due to quality brass. I mean I’m not going to sit down and fill 100 cases with h20 and check the difference I do 20 and that will gives me enough info that I’m looking for, It shows aswell when the sd and es is numbers lots of guys are looking for.
Sorry about my crappy wording hahaha apologies

Yeah, it tells you that you are still somewhere south of 100K. Good brass in a good rifle won't show any indication whatsoever at 70K. Pressure testing doesn't guess or read tea leaves.
If your goal is 70K, then I guess that's fine. One reason I don't shoot other people reloads.

 

[Potsie]

I’m curious how they handle mono’s?

 

[Dfoster]

Yeah, it tells you that you are still somewhere south of 100K. Good brass in a good rifle won't show any indication whatsoever at 70K. Pressure testing doesn't guess or read tea leaves.
If your goal is 70K, then I guess that's fine. One reason I don't shoot other

I’m curious how they handle mono’s?

 

[dsrtibb]

I’m curious how they handle mono’s?

I tested a few different badlands bullet before George the owner passed and they ran amazing. I currently run cutting edge in my 33 Moses and they shoot amazing. I'm also getting some hammer bullets for testing.

 

[mtmuley]

I tested a few different badlands bullet before George the owner passed and they ran amazing. I currently run cutting edge in my 33 Moses and they shoot amazing. I'm also getting some hammer bullets for testing.

Load the new Hammer HBC in your. 30 cal. It will reach 3800 fps in a .30-.338 Lapua Imp. mtmuley

 

[dsrtibb]

Load the new Hammer HBC in your. 30 cal. It will reach 3800 fps in a .30-.338 Lapua Imp. mtmuley

Working with Hammer to get bullets designed for the moses calibers. Currently have some 338s on the way and excited to see how they shoot.

 

[wilkup]

I’m curious how they handle mono’s?

132gr HHT in my 7 at 3200’
I’m also curious how the Hammers do will do in the 338 Moses so I bought a sample pack of the 190gr HHTs and sent them to Jeremiah to try in his 20” 338 Moses.

 

[dsrtibb]

132gr HHT in my 7 at 3200’
I’m also curious how the Hammers do will do in the 338 Moses so I bought a sample pack of the 190gr HHTs and sent them to Jeremiah to try in his 20” 338 Moses.

Yeah man, I'm excited for those to arrive.

 

[mtmuley]

I have a 300prc that does really well for me honestly not a bad rifle. Since my venture into the Moses cartridge it has opened my eyes a bit more.

I was kidding. Personally, I have no interest in them though. mtmuley

 

[Wind Gypsy]

There is nothing magic in the cartridge world. Body tapers, shoulder angles, capacity, freebore, yada yada. Someone coming along and telling you all about the magic shit they can sell you but cant lay out any basics of a cartridge design without an NDA is a pretty clear sign to run away IMO. Cant tell folks how far a shoulder is blown forward, what angle the shoulder is, h20 capacity, etc without an NDA?! Laffin! Very easily measured by anyone who sees one but do you make anyone who sees or handles one sign an NDA? Better not lose any brass at a match or the secret might get out!

Load the new Hammer HBC in your. 30 cal. It will reach 3800 fps in a .30-.338 Lapua Imp. mtmuley

Those little baby dick case necks probably aren't long enough to touch more than 1 drive band on a hammer. Could see that being pretty wonky with getting bullets seated concentric.

 

[dsrtibb]

There is nothing magic in the cartridge world. Body tapers, shoulder angles, capacity, freebore, yada yada. Someone coming along and telling you all about the magic shit they can sell you but cant lay out any basics of a cartridge design without an NDA is a pretty clear sign to run away IMO. Cant tell folks how far a shoulder is blown forward, what angle the shoulder is, h20 capacity, etc without an NDA?! Laffin! Very easily measured by anyone who sees one but do you make anyone who sees or handles one sign an NDA? Better not lose any brass at a match or the secret might get out!



Those little baby dick case necks probably aren't long enough to touch more than 1 drive band on a hammer. Could see that being pretty wonky with getting bullets seated concentric.

Triggered much?? must be on that side...lol

 

[Forkyfinder]

Triggered much?? must be on that side...lol

Nah - hes pretty smart on here and this shit actually.

I am curious how/why the short necks arent a challenge. It seems like setting neck tension would be difficult to maintain consistency, as well as concentricity.