millerkiller77
Well-known member
Did you machine 100% of that bolt?
Metalworking Hunttalkers!
- Thread starter p_ham
- Start date
millerkiller77
Well-known member
That looks good man! My only suggestion so far would be to ditch the doodoo bearings that came with the wheel and replace them with a quality set of Timken, SK , or comparable.
Your entire build is dependent on them two little chingadreros....
Thank you! I’ll try to find them
DouglasR
Well-known member
Do any of you guys know anything about crossmembers?
Obviously this one’s shot and kenworth want $850 which seems kinda high for a 2’ piece of c-channel.
Do you think a machine or welding shop could make one for cheaper?
Obviously this one’s shot and kenworth want $850 which seems kinda high for a 2’ piece of c-channel.
Do you think a machine or welding shop could make one for cheaper?
np307
Well-known member
I dont know a ton about that world but I believe there's some hardness and metallurgical specs on some of those frame pieces. Even something like drilling the frame for a tool box mount can be a no-go technically.
Now hypothetically, yeah a welding shop could probably take care of that cheaper.
My brother fixed one of the grain trucks last year by welding a doubler plate on the inside and then welding the crack. They've fixed a lot of grain and potato trucks like that over the years
np307
Well-known member
Replaced the saddles on an ammonia tank Tuesday. The previous ones were very nicely coped wood, probably locust, but one side had been exposed to the elements and started to rot so they got written up for it. No way to go back with another wood piece because the piping held it all pretty rigid. So we built some stainless trusses in place.
Then we had a request to build a pallet dragger for the dock at one of the plants. I got a very low quality video of one in use and had to guess at the specs from that. I think it turned out well though.
Then we had a request to build a pallet dragger for the dock at one of the plants. I got a very low quality video of one in use and had to guess at the specs from that. I think it turned out well though.
np307
Well-known member
A plant called yesterday needing an emergency piping change as ammonia was crossing into glycol lines. We surveyed, took measurements, and welded a couple pieces yesterday and then showed up at 0500 today to finish. 
np307
Well-known member
Pretty fun week, mostly rolling solo. Built a header for a valve cluster, finished up a hall tree, and made a piping change at one of the plants. Last one was a good chance to practice my isometric drawing.
np307
Well-known member
Capped a 3 inch ammonia line and started work on some 4 inch sch10 stainless (steam line to a heat exchanger) by getting a flange welded on. 
The winch mounted on my chipper was on there with some one inch washers to get the needed height when I purchased it. Knew the bolts would eventually have issues because the base of the winch was only sitting on those washers.
The bolts finally snapped and it was time to put in a strong, permanent mount.
And I was very happy with my midnight welds. It’s taken a while but they are coming along now. I think building the cart was good practice!
millerkiller77
Well-known member
I recommend you gusset the "load" side
np307
Well-known member
Nothing crazy interesting going on at work recently. Well, there were a few welds up against the ceiling but there might have been some not postable climbing methods involved.
Made some stainless pans to collect hydraulic oil under molding machines. No idea why they didn't let us make them from aluminum. This was one of the bigger fab projects I've done, used a manual brake for the pans and a press brake for the handles. Not very fun to bend the stainless by hand.
Currently we are demoing some fructose and sucrose lines to get a new sucrose system installed in January. No fun at all draining these lines.
Made some stainless pans to collect hydraulic oil under molding machines. No idea why they didn't let us make them from aluminum. This was one of the bigger fab projects I've done, used a manual brake for the pans and a press brake for the handles. Not very fun to bend the stainless by hand.
Currently we are demoing some fructose and sucrose lines to get a new sucrose system installed in January. No fun at all draining these lines.
np307
Well-known member
I could be hunting the rut right now. Instead I'm going to be staring at these all day.
I can not stand repetitious welding. I had to make shoe holders for a friend's wife. I politely asked how many she needed, thinking maybe 3, She asked for 10! Aluminum angle. Tried to bend the angles... snap. Then heating each bend... repetition kills creative builds for myself.
Had it been 3 I would have enjoyed the heck out of crafting though 10??? I put on the Amazon 80's rock music on the garage sound bar and went into assembly line work. I asked... Lesson learned.
Had it been 3 I would have enjoyed the heck out of crafting though 10??? I put on the Amazon 80's rock music on the garage sound bar and went into assembly line work. I asked... Lesson learned.
p_ham
Well-known member
Fired up the MIG for the 1st time in I don't even know how long. I'm a bit rusty, it's got some undercutting here and there. I bounced around to keep the heat manageable. Good enough for a bluing tank. I was able to use up some leftover 10ga sheet from when I built my bench.
np307
Well-known member
Been on several different projects recently. Forklift barrier in the cooler at a plant, repiped some tank connections, building more stainless pans to collect hydraulic oil, and some hose stands. 
blueridge
Well-known member
Always impressed with your welding skills, Nathan. Respect. 
np307
Well-known member
Appreciate it. I've still got plenty to learn but it's cool to do stuff that I know I wouldn't have been able to last year.Always impressed with your welding skills, Nathan. Respect.
np307
Well-known member
Boss got a call in the middle of a job yesterday from a new plant needing something built in a hurry. We showed up at 0830 today, took measurements, drew up a sketch, and got it built. I took care of the frame and boss did the sheet metal work. 
