Yeti GOBOX Collection

Search results

  1. G. McAlister

    NFA Wait Times

    I ordered one as well. Should be here sometime next week.
  2. G. McAlister

    NFA Wait Times

    Just got my ATF approval Tuesday. Took almost 8 months on the dot from submission to approval. Due to holiday mail slow down, fingerprint info took forever to get to SC, but still looking at less than 10 months from starting the process to approval. Should have can in hand within the next two weeks.
  3. G. McAlister

    FL Resizing Neck Issue

    From what I can measure it’s not bumping it at all. Length to where the shoulder starts and where it narrows to the neck are right at saami length. Also measured against virgin brass and found measurements to be the same
  4. G. McAlister

    FL Resizing Neck Issue

    I have found the issue, and as it turns out I AM THE IDIOT. Trialing the RCBS dies again today I decided to screw the die in further than the manufacturer recommendations. Fixed the problem instantly. Sorry for wasting everyone’s time on this. Thank you all for your help as well!
  5. G. McAlister

    FL Resizing Neck Issue

    1. Tested to find the most accurate. The brass represents three loads I made and one factory load. 2. New brass measures 2.0925, fired brass 2.0935
  6. G. McAlister

    FL Resizing Neck Issue

    I have a single stage Lee press. I have followed the manufacturer’s instructions for setting the die up to the proper distance from the ram. I have experimented by screwing the dies further down and also to less than touching the ram, using both the Lee and RCBS dies I have.
  7. G. McAlister

    FL Resizing Neck Issue

    It’s about the same really.
  8. G. McAlister

    FL Resizing Neck Issue

    It will chamber, just very tight bolt closure.
  9. G. McAlister

    FL Resizing Neck Issue

    That’s my next step, wanted to rule out any human error in the reloading process on my side before taking it to someone to check the chamber.
  10. G. McAlister

    FL Resizing Neck Issue

    Rubbing in the center of the chamber??
  11. G. McAlister

    FL Resizing Neck Issue

    A resized case will not fit in the chamber without a sticky bolt. Bullet seating has not changed between virgin brass and fired brass. Based on my COAL gauge the re-loaded brass is sticking before it fully sits in the chamber. Pic attached of virgin brass and re-sized and reloaded brass.
  12. G. McAlister

    FL Resizing Neck Issue

    Using same brand FL and seating dies. Seating die on new brass has caused zero issues with the brass. Diameter of fired neck is .346. I’m starting to think this is not a neck issue, but something else as some of the necks in the hard chambers are right at .344. I as far as .349, I believe my...
  13. G. McAlister

    FL Resizing Neck Issue

    Tried sharpie. I didn’t notice any rub marks in the neck or shoulder area.
  14. G. McAlister

    FL Resizing Neck Issue

    .300 WSM Trim case length 2.095” .349” neck diameter Bullets are measuring right at .308 Empty resized case neck is measuring at .340 I have not fired any of the resized reloads. I have fired the virgin brass with multiple loads, no issues
  15. G. McAlister

    FL Resizing Neck Issue

    Hey all, I am reloading 180 gr. TTSX in Norma brass. When loading a new cartridge everything is just fine and the loads cycle like butter. I’ve started processing through my once fired brass to re-size using a Lee FL re-sizing die. Upon reloading these once fired cartridges, they would barely...
  16. G. McAlister

    Another KY Gobbler

    Nice bird EKY. Hope you can drop a pin if I ever get over to that side of the state to hunt one.
  17. G. McAlister

    Suppressor Experience

    Big Fin can you advise where you ordered one from? I can’t find one anywhere.
  18. G. McAlister

    Getting old school, new tech-New CVA Scout 35 Whelen

    I may have some extra ammo laying around if someone needs some. I reload for the 35 and have tons of loaded ammo and components. Mine shoots great with 200 gr. TTSX
  19. G. McAlister

    50 years in Colorado- Relocated to Kentucky not a joke for real

    As I suspected we are neighbors. Shoot me a message if you need anything.
  20. G. McAlister

    50 years in Colorado- Relocated to Kentucky not a joke for real

    Lab, sounds like you might be my neighbor. Welcome to the Bluegrass state.

Latest posts

Forum statistics

Threads
113,670
Messages
2,029,077
Members
36,277
Latest member
rt3bulldogs

Share this page

Back
Top